Page History

...

1. Install Solutions Enabler.
   1. Select the destination folder.
   2. Select he Setup Type (use: Complete)
   3. On the Service List, use the defaults and also check the SYMAPI daemon checkbox.
   4. Click Next.
   5. Click Install.
2. If your SQL Server instance stores its data on CLARiiON or VNX storage arrays , the monitored server should be authorized using a SYMCLI command as follows:
   1. Make sure you have the array's Storage Processors (SP) hostname or IP address, and the array's administrator username and password.
   2. Open the command prompt.
   3. Navigate to the directory in which EMC Solutions Enabler is installed.
   4. Execute: SYMCLI\BIN\symcfg.exe authorization add -host {VNX-SP} -username {VNX Administrator} -password {VNX Administrator Password}
3. If your SQL Server instance stores its data on Symmetrix (DMX or VMAX) storage arrays, gatekeeper devices must be installed.
   1. Gatekeeper device is a small device (less than 3 MB) used by Solutions Enabler to improve the communication with the storage array. The assistance of a storage administrator is required.

   2. To verify which storage units and devices are attached to a monitored server, execute: SYMCLI\BIN\syminq.exe
      The following table shows an example of the command's output.

      Device		Product			Device
      Name	Type	Vendor	ID	Rev	Ser Num	Cap (KB)
      \\.\PHYSICALDRIVE0

       

      	SEAGATE	ST15150W	HP12	02994239	4194157
      \\.\PHYSICALDRIVE1

       

      	EMC	SYMMETRIX	5265	93052361	4224000
      \\.\PHYSICALDRIVE2

       

      	EMC	SYMMETRIX	5265	93052461	4224000
      \\.\PHYSICALDRIVE3

       

      		EMC	SYMMETRIX	5265	93052561	4224000
      \\.\PHYSICALDRIVE4	GK	EMC	SYMMETRIX	5265	93050161	2880
      \\.\PHYSICALDRIVE5	GK	EMC	SYMMETRIX	5265	93051161	2880

   3. Gatekeeper devices are marked with GK in the Type column. The two most left digits (93 in this example) are the suffix of unit ID.
   4. If gatekeeper devices are missing, ask the storage administrator to define them. To verify, execute SYMCLI\BIN\syminq.exe and check its output once again.
4. If the monitored SQL Server instance runs on a VMware guest server, the monitored server should be authorized using a SYMCLI command as follows:
   1. Make sure you have the ESX server hostname or IP address, and the ESX server's administrator username and password.
   2. Open a command prompt.
   3. Navigate to the directory in which EMC Solutions Enabler is installed.
   4. Execute: SYMCLI\BIN\symcfg.exe authorization add -host {ESX server} -username {ESX server Administrator} -password {ESX server Administrator Password} -vmware

5. If the monitored SQL Server instance runs on a Microsoft Hyper-V guest server, the monitored server should be authorized using a SYMCLI command as follows:

   Info
   title Note
   Only pass-through devices are supported. Devices configured as VHD are not supported.

   1. Make sure you have the Hyper-V hostname or IP address, and Hyper-V's administrator username and password.
   2. Open a command prompt.
   3. Navigate to the directory in which EMC Solutions Enabler is installed.
   4. Execute: SYMCLI\BIN\symcli.exe authorization add -host {Hyper-V hostname} -username {Hyper-V Administrator} -password {Hyper-V Administrator Password} -hyperv
6. Initialize Solutions Enabler (building the symapi\db\symapi_db.bin file}.
   1. Open a Windows command prompt.
   2. Change to the directory in which the EMC Solutions Enabler is installed.
   3. Execute the discover command:
      SYMCLI\BIN\symcfg.exe discover -all
      This time, "No devices were found" message should be considered an error. If no devices were found, retry carefully steps 1 to 6. If still not found, open a support case using the IDERA community portal.

   4. If your SQL Server instance stores its data on Symmetrix (DMX or VMAX) storage arrays, execute SYMCLI\BIN\symcfg.exe list
      Its output should list all attached Symmetrix storage units. Each of the units that are actually used to store SQL Server DB files should be marked as local in the Attachment column. See example:

      Symmetrix	Attachment	Model	Version
      000190103692	Remote	DMX3-24	5773
      000190765393	Local	VMAX-1	5875

   5. If your SQL Server instance stores its data on VNX or CLARiiON storage arrays, execute SYMCLI\BIN\symcfg.exe list -clariion
      Its output should list all attached VNX and CLARiiON storage units.

...

1. Select a database file that is stored on an EMC sorage array (file size must be > 0).
2. Open a Windows command prompt.
3. Navigate to the directory in which the EMC Solutions Enabler is installed.
4. Execute: SYMCLI\BIN\symrslv.exe file <full path and name of the selected DB file>
5. The output should contain a table with the following column titles:
   Size, Array, Dev, Offset, PPdevName, Offset, and Attr.
   Array and Dev should present EMC unit and EMC device. If "N/A" is presented instead, then EMC Solutions Enabler failed to map the file. In this case, open a support case using the IDERA community portal.

...

...

...

Save